Cyclonic Separation
120v HEPA Dust Extractor

HEPA Pro LP MAX
120 Volt, 300 CFM, 100" H20

Q3 PROMOTION 

$2,690.00      

120v, 300-CFM, 110" H20 — Sustained Suction

Vacuum Anything ---
Without Damaging The Cyclone Module:

• Ultra fine powders, sticky terrazzo, coatings, glue, moist debris, food waste, green concrete, etc.

• CYCLONE MODULE - Made of steel, can't be damaged or compromised, 100% washable if you want too (not necessary)

• Maintained Performance & Superior Life - Unlike a pleated cartridge filter that is instantly compromised, suction immediately being to drops, and it's a consumable cost.

AAAAA

No Pre-Filter

• With NO pre-filter to blind, cake, clean or replaced, the motors and a 20-amp circuit don’t get hot

• Electrical power and sustained suction are maintained.

No Reverse Pulse Filter Cleaning

• True cyclonic separation

• No self, semi, or automatic filter cleaning because there is no pre-filter!

Powerful Lift ---
More Than Just A Dust Extractor:

• DUAL CYCLONIC SEPARATION - Picks-Up Heavy Construction Debris!

• Separates & directs over 99% of the collected debris - dry powders, sludge, hot coating material, chunks of concrete, steel shavings, etc. - to the external Longopac® collection bag — the cyclone and the HEPA filters stay remarkably clean!

• PRODUCTIVITY & PERFORMANCE - Without a filter to blind:

  • The motors and circuit don't overheat

  • Powerful suction is maintained!

Suction Starts @ 300-CFM, Stays @ 300 CFM

• Without a pre-filter to blind and cause suction drop and overheating, suction is sustained from a 120 volt, 20 amp circuit

• MOTORS:  powered by two (2) 120 volt HEPA Pro Backpack Vacuums, each at:  1200 Watt, 10.0 Amp, 150 CFM, 100" H20

KEY PERFORMANCE ADVANTAGES

HEPA FILTER SYSTEM - CERTIFIED

EXCEEDS EPA RRP & OSHA SILICA DUST STANDARDS

Individually tested and certified to be 99.97% efficient at .3 microns with test label affixed to the filter (pic, right.)  CERTIFICATION LABEL, complete with airflow and penetration rate numbers and individual serial number.

BUYER BEWARE, "It's Your Responsibility"

• As per the OSHA Silica Dust Regulation:  it is the customer's responsibility (not the manufacturer) that the dust extractor operates and is maintained to perform at the stated specifications.

• Routine Cleaning & Replacement of Pre-Filters in a Dust Extractor --- an unhealthy and costly chore.  Consult the owners manual of your dust extractor, but not all filters are washable and using an air compressor (besides being unhealthy and unsafe), is not allowed as per the OSHA Silica Dust Rule.

20" Pro Sweep Floor Brush & 50" S-Wand (included with the TB300.)

POWERFUL LIFT - as effective and productive as the TB300 is as a dust extractor for silica dust extraction, its impressive combination of 300 CFM and 100" of H20 makes the TB300 exceptional at sweeping floors after grinding and sawing operations.

Professional Floor Sweep Tools  --- included with the TB300.  Constructed of HD aluminum with adjustable wheels and brushes, you can expect to vacuum the finest dust particles from every conceivable surface type including the full width of its 20" brush! < Click here for Replacement Floor Brush & Wand >

Micro-Fiber Collection Bags - Collects the ultra-fine powder that escapes the cyclonic separation - the upstream filter that keeps the HEPA filters clean.

When vacuuming dry powder, bag replacement is typically after collecting 200 pounds in the Longopac® bag.

Micro-Fiber Collection Bag, 10-Pk
#122-3228-14     $40.00